多槽手動超聲波清洗機應用于工業領域和清洗行業，且使用效果非常的好，在市場中很受歡迎，當然使用期間難免會遇到一些問題，下面就來講幾個常見的，以便您多預防。

The multi slot manual ultrasonic cleaning machine is applied in the industrial field and cleaning industry, and the use effect is very good. It is very popular in the market. Of course, it is inevitable to encounter some problems during use. Here are some common ones for you to prevent more.

1、多槽手動超聲波清洗機打開電源開關，指示燈不亮。這種情況維修時須檢查電源開關是否完好，漏電開關是否合上。如果開關完好再檢查保險絲是否過載熔斷，基本上可以。

1. Turn on the power switch of the multi tank manual ultrasonic cleaning machine, and the indicator light does not light up. In this case, check whether the power switch is in good condition and whether the leakage switch is closed. If the switch is intact, check whether the fuse is overloaded and blown, which can be basically solved.

2、多槽手動超聲波清洗機打開電源開關后，指示燈亮，但沒有超聲波輸出。這種情況比較復雜，維修時檢查換能器與超聲波功率板的連接插頭是否有松脫，然后檢查保險絲是否熔斷。

2. After turning on the power switch of the multi tank manual ultrasonic cleaning machine, the indicator light is on, but there is no ultrasonic output. This situation is complicated. During maintenance, first check whether the connecting plug between the transducer and the ultrasonic power board is loose, and then check whether the fuse is blown.

如果一切正常有可能是超聲功率發生器內部故障，用萬用表打電源線明線，火線是否都通。在排除了發生器故障后再檢查超聲波換能器是否燒壞，是否需要更換。

If everything is normal, it may be the internal fault of the ultrasonic power generator. Use a multimeter to open the power line and check whether all the live wires are connected. After troubleshooting the generator, check whether the ultrasonic transducer is burnt out and needs to be replaced.

3、多槽手動超聲波清洗機直流保險絲熔斷。可能是整流橋堆或功率管燒毀，也可能是換能器老化，電流不穩，這些都可能造成電源發生器故障。維修時要多加注意。

3. The DC fuse of the multi slot manual ultrasonic cleaner is blown. It may be that the rectifier bridge stack or the power tube is burnt, or the transducer is aged and the current is unstable, which may cause the power generator failure. Pay more attention to maintenance.

注意：

be careful:

使用多槽超聲波清洗機清洗工件時，需要注意槽液不能裝得太滿，以免出現兩槽超聲波清洗劑相互混合，清洗籃底部粘液被排出的現象。此外，清洗機的每個槽都應該是獨立的操作過程，因此注意不要將兩個槽的清洗劑串聯使用，也不要人為減少操作過程和清洗操作時間。

When using the multi tank ultrasonic cleaning machine to clean the workpiece, it should be noted that the tank liquid cannot be filled too full, so as to avoid the phenomenon that the two tanks of ultrasonic cleaning agents are mixed with each other and the mucus at the bottom of the cleaning basket is discharged. In addition, each tank of the cleaning machine should be an independent operation process, so pay attention not to use the cleaning agents of the two tanks in series, nor artificially reduce the operation process and cleaning operation time.

多槽手動超聲波清洗機常見三種問題以及有關注意事項就講解到這里了，您多預防問題才是根本，更多信息獲取就來我們網站gzhgn.cn咨詢吧！

Here are the three common problems and relevant precautions of multi tank manual ultrasonic cleaning machine. How to prevent problems is the root. For more information, please come to our website gzhgn.cn!